On Plaster Washers

Before the advent of prefabricated wallboard or “drywall” in the 1940s and ‘50s, plaster was the material of choice for interior walls and ceilings in American homes. Portland cement plaster was painstakingly hand-troweled onto wood slats (lathing) nailed to the wall and ceiling framing. The excess plaster that dries behind and around the lath is referred to as the “key” – essentially locking the plaster to the lath. The key prevents the installed plaster from pulling away from the lath. Ample fastening prevents the lath from pulling away from the framing. Thus, the best laid plans of mice and men.

Plaster is a fabulous interior finish. It is strong, has a uniform finish and can last forever. The obvious question is; “why isn’t it used as it once was?” The answer is simple – money! Interior lath and plaster is expensive. Drywall is cheaper to produce and install.

Like anything else, plaster has its drawbacks – price aside. Anyone with plaster can tell you how it cracks and just try hanging a picture in plaster – yikes! And a plaster finish is infinitely more difficult to patch than drywall.

One of the most common problems with plaster is a sagging ceiling. This occurs when the key breaks and positive connection to the lath is lost. However, a sagging ceiling isn’t always caused by a broken key. Often it is caused when someone missteps in the attic – setting foot on the lath rather than on ceiling joist. Such was the case in the holiday classic movie National Lampoons Christmas Vacation when a bumbling and unsuspecting Chevy Chase went crashing through the ceiling onto a bunk bed below.

Many years ago a caller to our nationally syndicated radio program made us aware of a little known plaster repair device called a “plaster washer,” – a round metal disc about the size of a quarter (actually about one inch in diameter), which is used to hold up a sagging ceiling. The disc has a countersunk hole in the center through which a drywall screw is inserted. The disc also has many smaller holes scattered throughout its body into which spackle or drywall joint compound attaches itself to conceal the repair.

Here’s how to take the sag out of your plaster ceiling using these nifty little gadgets. First, using an old chisel or putty knife, remove any loose or crumbling plaster in the area that is to be repaired. Slightly undercut the edges of the existing plaster to create a solid bond with the new plaster. Use a vacuum with an upholstery attachment along with an old paint brush to remove dust and surface debris.

Next, insert a galvanized drywall screw (1 5/8 to 2 inches) through the center hole of the plaster washer and place the screw head into a #2 bit on a screw gun. Drive the screw through the plaster and into the wood lath a couple inches back from the edge of the hole or crack to be repaired. Tighten down the drywall screw just enough to pull the sagging plaster up against the lath and flatten out the convex shaped washer. If the plaster does not pull up and/or the screw does not tighten up, you have likely missed the lath and should back out the screw and move it slightly in one direction or the other. Keep in mind that there is a slight space between each strip of lath. Install several plaster washers around the area to be repaired. If there is evidence that the lath is not securely fastened to the framing, use longer drywall screws in combination with the plaster washer and drive the screws through the plaster and lath and into the framing.

Once the plaster has been resecured to the lath, using a six inch taping knife, apply a plaster patching compound to fill in the hole or crack. Prior to applying the patch material, spray the lath and existing plaster with water. This will prevent moisture from being sucked out of the new patch material, which could result in cracking and a poor bond. Small cracks can be filled with a paintable caulk. Allow the patch to dry overnight and then sand it level using 100 grit sandpaper and a sanding block.

Conceal the plaster patch and the plaster washers by covering them with a self adhesive fiberglass mesh joint tape. Use the six inch taping knife to apply a thin coat of drywall joint compound over the patch area. Feather the joint compound at the edges of the patch. Allow the joint compound to dry overnight and apply a second coat overlapping the first coat by a couple of inches in all directions. Allow the material to again dry overnight and lightly sand using 100 grit sandpaper or sanding mesh along with a sanding pad or block. Additional coats of joint compound and sanding may be required to achieve the desired finish.

After the final sanding, use a damp rag and/or a tack cloth to clean the patch area and prepare it for painting. Prime the patch with a high quality interior acrylic latex primer and, when dry, apply one to two coats of paint to match the existing finish.

Since you will be working overhead and stirring up quite a mess, be sure to wear safety glasses, a dusk mask and a ball cap. It wouldn’t hurt to use drop cloths to cover furniture or other valuables that could be dirtied or damaged.

Related Posts

• 

  Show Notes: What “Wood” The Carey Bros Do?
  Show Notes: What “Wood” The Carey Bros Do?
• 

  Transforming Walls Into Smart Surfaces
  Transforming Walls Into Smart Surfaces
• 

  Creating a dream home with cypress
  Creating a dream home with cypress
• 

  Tip of the Day: Walls, What’s In There?
  Tip of the Day: Walls, What’s In There?

You must be logged in to post a comment Login